Basic Suunto EON Steel downloading copied from my test application.
This parses all the core dive data, including sample data (time, depth,
cylinder pressure, deco information etc).
The deco information returns ceiling and TTS rather than ceiling and
"time at ceiling", because that's what the dive computer has, and I
don't see any other way to return the information.
We don't report any events yet, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are two different ways to specify the volume of a tank. In the
metric system, the tank volume is specified as the water capacity, while
in the imperial system the tank volume is specified as the air capacity
at the surface (1 ATM) when the tank is filled at its working pressure.
To avoid mistakes, the tank volume is now always returned as the metric
volume. For imperial tanks, the tank volume is converted to the metric
representation.
Devices that only reports a single temperature in the header
will now be able to report it as well when they implement this.
Signed-off-by: Calle Gunnarsson <calle.gunnarsson@gmail.com>
Starting with firmware v1.23, the OSTC3 settings can be configured
through the USB interface. There are new commands for reading, writing
and restoring the settings to their default values.
The Uwatec Meridian protocol is identical to the Uwatec Smart/Galileo
protocol, except for some additional framing around each data packet,
and the switch from IrDA to usb-serial communication. For parsing, the
data format appears to be identical to the Galileo data format.
This event is on when accumulating deco time. Once you reach the floor
deco time will start decreasing and the event will stop. Going below the
floor again will re-activate the event.
Signed-off-by: Michael Andreen <harv@ruin.nu>
Unlike the corresponding mktime C library function, the libdivecomputer
function will never modify its argument. By marking the parameter as
const this is made more explicit.
Although the communication protocol of the OSTC3 is nearly identical to
that of the Frog, the different size parameters make it hard to share
the code easily. On top of that, if we ever implement native bluetooth
communication support, we'll need a completely separate backend anyway.
Therefore the Frog backend is simply duplicated, with a few OSTC3
specific changes applied here and there.
The existing ostc parser is upgraded to support the new OSTC3 data
format.
The Petrel (with updated firmware) supports an enhanced communication
protocol, which is more efficient and powerfull than the legacy Predator
compatibility mode. The new protocol uses data compression for faster
transfers and supports the ability to selectively download individual
dives. Last but not least, the new protocol isn't limited to the last
128kB of logbook data, but can access the full logbook capacity (16MB).
With the new interface, an application can easily retrieve the
underlying transport type from the device descriptors and present a
custom user interface element to the end-user for supplying transport
specific parameters. For example the serial port for devices using
serial communcication.
For devices using a usb-serial chipset or the bluetooth Serial Port
Profile (SPP/rfcomm), the transport type is DC_TRANSPORT_SERIAL, because
internally the serial emulation layer is used for the communication.
This is only a preliminary version. There is certainly some room for
improvement, but the basic functionality is already in place. That
should be sufficient for daily use, and possibles issues can always be
fixed when discovered.
The application shouldn't have to deal with the delay between packets.
If the default value isn't good enough, that should be fixed internally
and not on the application side.
The SAFETYSTOP is conceptually somewhere in between the NDL and the
DECOSTOP, so it makes sense to re-order the constants in the enum to
reflect this order.
The new vendor event provides a mechanism to deliver auxiliary data,
which is automatically retrieved during the data transfer, but not
accessible through the library interface otherwise. Possible examples
include handshake data and/or device identification data.
This event is mainly intended for diagnostic purposes, in combination
with the memory dumping support. Very few applications will actually
need it for anything else.
The Nemo Wide 2 uses the same communication protocol as the Icon HD,
except for two differences:
The Nemo Wide 2 requires a different baudrate and parity setting.
Unfortunately it doesn't seem possible to autodetect the correct
protocol variant at runtime. Attempting to proceed with incorrect
settings will render the device unresponsive and requires a battery
reset to recover.Therefore the model code needs to be provided as an
extra parameter, when opening the connection.
The Nemo Wide 2 also appears to have trouble downloading the entire
memory with a single request. Therefore the single large request is
split into many smaller ones. The offical Mares application uses 256
byte packets, and so do we. The Icon HD keeps using the large packets
because they are significant faster.
The extra model parameter breaks backwards compatibility!
Having these as events seems less useful since for many dive computers
there are data with every sample - so it makes much more sense to have
these as part of the sample.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
So far only OSTC and Shearwater Predator are supported. For the OSTC we
support CNS and setpoint changes in the samples (the current hardware
doesn't actually support ppO2 sensors and for the older hw that does I
don't have the correct encoding information).
For the Predator we support only the "average ppO2 during the sample".
The Predator also gives us a CNS value at the end of the dive - I don't
quite know yet how to deliver that back to the consumer. Possibly as CNS
value in the very last sample? That would at least be consistent.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
The Uwatec Smart protocol supports reading individual settings. However
the version functions only reads those three values that we use
internally (model, serial number and device clock). That's a very
arbitrary subset and it would be much better to support reading
specific values. But that's something for later...
The version function requires device specific knowledge to use it (at
least the required buffer size), it is already called internally when
necessary, and only a few backends support it. Thus there is no good
reason to keep it in the high-level public api.
These macros are used internally and don't need to be exposed. In some
cases, the actual values are not even constant, but dependant on the
model and/or the firmware version.
- PO2 warnings (high and low both mapped to the same SAMPLE_EVENT_PO2
event)
- SPEED warning (which according to hw isn't emitted at this point)
- Deco stop violations (both deep and regular mapped to same
SAMPLE_EVENT_CEILING event)
- Deco ceiling and time (this is reported as a series of
SAMPLE_EVENT_DECOSTOP events with packed deco stop depth (in m) and
time (in seconds)
A SAMPLE_EVENT_NDL event (with an optional value indicating the non-stop
time remaining) indicates that the ceiling has been resolved
- Gas change (reported as SAMPLE_EVENT_GASCHANGE2, using another
unfortunate O2% / He% semantic that is used in the
SAMPLE_EVENT_GASCHANGE
This also covers the manual gas set event of the OSTC
- Manual Marker (reported as SAMPLE_EVENT_BOOKMARK)
The two new events (SAMPLE_EVENT_GASCHANGE2 and SAMPLE_EVENT_NDL are added
to the universal app as well.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
The public api is changed to require a context object for all
operations. Because other library objects store the context pointer
internally, only the constructor functions need an explicit context
object as a parameter.
An application can now register an application defined callback
function, which will perform the actual logging. This provides
additional flexibility compared to logging to stderr with a hardcoded
format. Applications can now easily display the messages in their user
interface, customize the format, etc.
Although the internal logging function is a printf like function, the
arguments are converted into a plain string before being passed to the
callback function. This greatly improves interoperability with
programming languages which don't support C style variadic functions
(e.g. Python, C#, etc).
With the introduction of a context object, library initialization and
shutdown can be performed without requiring any global state. A single
process can use multiple independent contexts without any problems. The
lack of a global state also improves the thread-safety of the library.
At the moment, the new context object is primary used to implement an
improved logging system.
The devinfo and clock event data is now cached internally at the device layer.
This allows the new dc_parser_new() convenience function to retrieve the event
data directly from the device handle, and applications don't have to deal with
the events anymore to create a parser.
With the introduction of the device descriptors, the new dc_device_open()
convenience function can take care of the mapping from a particular model to
the corresponding backend internally, without needing any device specific
knowledge in the application. An application can simply query the list of
supported devices, and the library will automatically do the right thing.
Applications can now enumerate all the supported devices at runtime,
and don't have to maintain their own list anymore. The internal list
does include only those devices that have been confirmed to work at
least once without any major problems.
As the name already indicates, a device descriptor is lightweight
object which describes a single device. Currently, the api supports
getting the device name (vendor and product) and model number. But
this can extended with other features when necessary.
Adding the "dc_" namespace prefix (which is of course an abbreviation
for libdivecomputer) should avoid conflicts with other libraries. For
the time being, only the high-level device and parser layers are
changed.
The public header files are moved to a new subdirectory, to separate
the definition of the public interface from the actual implementation.
Using an identical directory layout as the final installation has the
advantage that the example code can be build outside the project tree
without any modifications to the #include statements.
